A.router-id 1.2.3.4
B.router-id 2011：：1
C.router-id Loopback0
D.router-id FF02：：5
您可能感兴趣的试卷
你可能感兴趣的试题
A.filter-list
B.inbound ACL
C.route-map
D.outbound ACL
E.prefix-list
F.neighbor 10.0.0.1 deny-map my-map command
A.configuring EIGRP stubs
B.configuring a second EIGRP AS and redistributing
C.configuring summary addresses
D.configuring an offset-list
E.configuring a prefix-list
F.configuring unicast neighbors
A.It will fragment the packet at Layer 2.
B.It will fragment the packet at Layer 3.
C.It will drop the packet and send an ICMPv6 message "packet too big" back to the source.
D.It will drop the packet.
A.ldp explicit-null
B.mpls forwarding explicit-null
C.mpls ldp advertise-labels explicit null
D.mpls ldp explicit-null
A. O IA
B. O E1
C. O E2
D. O
A.only the local OSPF routes
B.only the OSPF routes installed in the routing table
C.only the remotely learned OSPF routes
D.all the OSPF routes from the OSPF database that are eligible to be put in the routing table
A.VRF definition for IPv6
B.MP BGP for IPv6
C.LDP
D.VRF-enabled routing protocol
E.VRF-enabled interface
A.ipv6 router rip ccie distribute-list..
B.ipv6 router rip ccie offset-list..
C.interface e0/0 ipv6 rip ccie distribute-list..
D.interface e0/0 ipv6 rip ccie advertise..
A.Out-of-profile packets are queued.
B.It causes TCP retransmits.
C.Marking and remarking are not supported.
D.It does not respond to BECN and foresight messages.
E.It uses a single- and two-bucket mechanism for metering.
Refer to the exhibit. R2 and R3 are routers connected using Ethernet services from a service provider and can receive pings from each other. OSPF is configured as the routing protocol but adjacency is not happening. According to the output of the show commands in the exhibit， what could be the most likely cause of the problem？ （）
A. Ethernet interfaces were configured as point-to-point.
B. Process IDs are not matching.
C. Configured bandwidths do not match on both interfaces.
D. Broadcasts and multicast are not being propagated over the Ethernet services.
E. OSPF cost does not match on both interfaces.
最新试题
When STP UplinkFast is enabled on a switch utilizing the default bridge priority， what will the new bridgepriority be changed to？（）
Which message type is constructed and sent from an MSDP router to its MSDP peers when it receives a PIM register message knowing that the MSDP router is also configured as an RP for the PIM domain？（）
In order to configure two routers as anycast RPs， which of these requirements， af a minimum， must besatisfied？（）
Which three options are valid ways to filter routes from a BGP peer？（）
How does an IPv6 router deal with a packet that is larger than the outgoing interface MTU？（）
In PIM-SM what control plane signaling must a multicast source perform before it begins to send multicasttraffic to a group？（）
Which of these best describes the actions taken when a VTP message is received on a switch configuredwith the VTP mode "transparent"？（）
Which types of prefixes will a router running BGP most likely advertise to an IBGP peer， assuming it is notconfigured as a route reflector？（）
Two routers configured to run BGP have been connected to a firewall， one on the inside interface and one on the outside interface. BGP has been configured so the two routers should peer， including the correctBGP session endpoint addresses and the correct BGP session hop-count limit EBGP multihop. What is agood first test to see if BGP will work across the firewall？（）
Which two statements are true about RED？（）