A. O IA
B. O E1
C. O E2
D. O
您可能感兴趣的试卷
你可能感兴趣的试题
A.only the local OSPF routes
B.only the OSPF routes installed in the routing table
C.only the remotely learned OSPF routes
D.all the OSPF routes from the OSPF database that are eligible to be put in the routing table
A.VRF definition for IPv6
B.MP BGP for IPv6
C.LDP
D.VRF-enabled routing protocol
E.VRF-enabled interface
A.ipv6 router rip ccie distribute-list..
B.ipv6 router rip ccie offset-list..
C.interface e0/0 ipv6 rip ccie distribute-list..
D.interface e0/0 ipv6 rip ccie advertise..
A.Out-of-profile packets are queued.
B.It causes TCP retransmits.
C.Marking and remarking are not supported.
D.It does not respond to BECN and foresight messages.
E.It uses a single- and two-bucket mechanism for metering.
Refer to the exhibit. R2 and R3 are routers connected using Ethernet services from a service provider and can receive pings from each other. OSPF is configured as the routing protocol but adjacency is not happening. According to the output of the show commands in the exhibit, what could be the most likely cause of the problem? ()
A. Ethernet interfaces were configured as point-to-point.
B. Process IDs are not matching.
C. Configured bandwidths do not match on both interfaces.
D. Broadcasts and multicast are not being propagated over the Ethernet services.
E. OSPF cost does not match on both interfaces.
A.instances can control a selection of VLANs
B.load balancing
C.fast transition to forwarding state
D.backbone,uplink,and portfast (or equivalent)
E.root,loop,and BPDU guard (or equivalent)
A.the table of 4096 elements that map the respective VLAN to STP instance number
B.VTP version
C.configuration revision number
D.native VLAN ID
A.PIM sparse mode is being used.
B.PIM dense mode is being used.
C.The BGP multicast address family has not been configured.
D.IGMP version 3 is being used.
E.IP PIM neighbor filters have not been applied.
A.ip sla 1 icmp-echo 1.1.1.1 tos 160
B.ip sla 1 icmp-echo 1.1.1.1 tos 20
C.ip sla 1 icmp-echo 1.1.1.1 precedence 5
D.ip sla 1 icmp-echo 1.1.1.1 dscp 20
A.The phones are not sending traffic with the correct DSCP value.
B.The Cisco CallManager is not marking the traffic correctly.
C.This is most likely a bug on the CE routers.
D.Your LAN QoS is incorrectly configured.
最新试题
Choose two commands that are required to enable multicast on a router, when it is known that thereceivers use a specific functionality of IGMPv3.()
Which two statements about SA caching are true?()
When STP UplinkFast is enabled on a switch utilizing the default bridge priority, what will the new bridgepriority be changed to?()
Which two EIGRP options will limit a query domain?()
In GLBP,which router will answer on client ARP requests?()
Which types of prefixes will a router running BGP most likely advertise to an IBGP peer, assuming it is notconfigured as a route reflector?()
What is true about Unicast RPF in strict mode?()
What is the command to configure RSVP to reserve up to one-tenth of a Gigabit link,but only allow eachindividual flow to use 1 MB/s?()
Which message type is constructed and sent from an MSDP router to its MSDP peers when it receives a PIM register message knowing that the MSDP router is also configured as an RP for the PIM domain?()
Which three message types are valid PIMv2 message types?()