Which command can be...

单项选择题Which command can be used to filter a RIPv6 route from getting installed in the routing table？（）

A.ipv6 router rip ccie distribute-list..
B.ipv6 router rip ccie offset-list..
C.interface e0/0 ipv6 rip ccie distribute-list..
D.interface e0/0 ipv6 rip ccie advertise..

点击查看答案

您可能感兴趣的试卷

你可能感兴趣的试题

1.多项选择题Which three statements are true about policing？（）

A.Out-of-profile packets are queued.
B.It causes TCP retransmits.
C.Marking and remarking are not supported.
D.It does not respond to BECN and foresight messages.
E.It uses a single- and two-bucket mechanism for metering.

点击查看答案

2.单项选择题 Refer to the exhibit. R2 and R3 are routers connected using Ethernet services from a service provider and can receive pings from each other. OSPF is configured as the routing protocol but adjacency is not happening. According to the output of the show commands in the exhibit， what could be the most likely cause of the problem？（）

A. Ethernet interfaces were configured as point-to-point.
B. Process IDs are not matching.
C. Configured bandwidths do not match on both interfaces.
D. Broadcasts and multicast are not being propagated over the Ethernet services.
E. OSPF cost does not match on both interfaces.

点击查看答案

3.多项选择题Which two are natively included by the IEEE 802.1w standard？（）

A.instances can control a selection of VLANs
B.load balancing
C.fast transition to forwarding state
D.backbone，uplink，and portfast （or equivalent）
E.root，loop，and BPDU guard （or equivalent）

点击查看答案

4.多项选择题Which two attributes need to match for two switches to become members of the same MST region？（）

A.the table of 4096 elements that map the respective VLAN to STP instance number
B.VTP version
C.configuration revision number
D.native VLAN ID

点击查看答案

5.单项选择题Multicast is being deployed in the network， and only ip pim sparse-dense mode has been configured on allinterfaces in the network to support a new video streaming application. No other multicast configuration wasapplied anywhere in the network. Since enabling multicast， the network monitoring tools show periodic spikes in link utilization throughout the network， even in areas where the video application is not being used.What could be a possible cause？（）

A.PIM sparse mode is being used.
B.PIM dense mode is being used.
C.The BGP multicast address family has not been configured.
D.IGMP version 3 is being used.
E.IP PIM neighbor filters have not been applied.

点击查看答案

6.单项选择题Which configuration would make an IP SLA probe use a precedence value of 5？（）

A.ip sla 1 icmp-echo 1.1.1.1 tos 160
B.ip sla 1 icmp-echo 1.1.1.1 tos 20
C.ip sla 1 icmp-echo 1.1.1.1 precedence 5
D.ip sla 1 icmp-echo 1.1.1.1 dscp 20

点击查看答案

7.单项选择题You are the network administrator of an enterprise company that just deployed a global IP telephonyenvironment. In order to guarantee good voice quality，you asked your provider to implement QoS on the CE routers of your MPLS network. On your LAN，you have also deployed QoS.Users，however，keep complaining about bad voice quality，and the provider does not see matches on the DSCP values that you have asked him to match upon. What is most likely the problem？（）

A.The phones are not sending traffic with the correct DSCP value.
B.The Cisco CallManager is not marking the traffic correctly.
C.This is most likely a bug on the CE routers.
D.Your LAN QoS is incorrectly configured.

点击查看答案

8.单项选择题You are the network administrator of a Layer 3 switched network. Users in one VLAN are complaining thataccess to the server VLAN is very slow from time to time. Traffic in the local VLAN works without any issue，and users in other VLANs do not have any complaint to reach the server VLAN. What is most likely thecause of this issue？（）

A.routing issue
B.denial-of-service attack
C.MAC flooding
D.spanning-tree recalculation
E.Layer 2 loop
F.ARP spoofing attack

点击查看答案

9.单项选择题You are deploying two core switches， one in each building， 50 km away from each other. The cross-connection between them will be a Layer 2 2-gigabit EtherChannel with an 802.1Q trunk. You configured it correctly but the link does not come up. The port is in the "admin up" state， and the line protocol is in the "down" state. The fiber link is OK. What would be the most likely reason for the link not to come up？（）

A. The switches are not the same model
B. You are not using the correct SFP
C. You are not using correct optical media converters
D. Configuration should be modified， because the distance is longer

点击查看答案

10.多项选择题Your company is researching a new application that runs over IPv6， but part of it must still have IPv4 support. Your company uses a traditional IPv4 network. Your plan is not to run IPv6 over the whole network， but to segment parts of the network or even to operate simultaneously with IPv6 and IPv4. You must make a brief presentation about IPv6 technology to the board of technical directors. Which three of these items could be part of your presentation？（）

A. Tunnel IPv6 over IPv4 to connect far-end IPv6 networks
B. Explain why configuring IPv4 and IPv6 at the same time over the same LAN interface is not possible
C. Explain why configuring IPv4 and IPv6 at the same time over the same LAN interface is possible
D. What is the meaning of EUI-64 and how does it work？
E. Tunnel IPv4 over IPv6 to connect far-end IPv4 networks.

点击查看答案