A. The Layer 2 multicast address of the destination node
B. The solicited node multicast address of the destination node
C. The Layer 2 address of the destination node based on the destination IPv6 address
D. The IPv6 address of the destination node based on the destination Layer 2 address
您可能感兴趣的试卷
你可能感兴趣的试题
A.6to4
B.6over4
C.ISATAP
D.GRE
A.0.0.0.1
B.0.255.0.1
C.2001：DB8：：1
D.2001：DB8：ABCD：FEEF：：1
A.2001：DB8：：1 and 2001：DB8：：2
B.2001：DB8：：9 and 2001：DB8：：10
C.2001：DB8：：10 and 2001：DB8：：17
D.2001：DB8：：1 and 2001：DB8：：18
A.The autoconfig command is missing from the router interface.
B.IPv6 multicast routing is not enabled on the router interface.
C.IPv6 unicast routing is not enabled on the router interface.
D.The router interface is configured with a /63 mask.
E.The router interface is configured with a /65 mask.
A. anycast address
B. site-local multicast
C. global address of the link
D. unique local address
E. link-local address
A.On-Passive
B.On-Auto
C.Passive-Active
D.Desirable-Auto
E.Active-Active
F.Desirable-Desirable
A. IPv6 prefixes
B. link-local addresses
C. solicited node multicast addresses
D. IPv6 prefixes and topology information
A. An IPv4-compatible tunnel is a static tunnel， but an 6to4 tunnel is a semiautomatic tunnel.
B. The deployment of a IPv4-compatible tunnel requires a special code on the edge routers， but a 6to4 tunnel does not require any special code.
C. An IPv4-compatible tunnel is typically used only between two IPv6 domains， but a 6to4 tunnel is used to connect to connect two or more IPv6 domains.
D. For an IPv4-compatible tunnel， the ISP assigns only IPv4 addresses for each domain， but for a 6to4 tunnel， the ISP assigns only IPv6 addresses for each domain.
A.configure a hard-to-guess VTP domain name
B.use a hard-to-guess VTP password
C.use VTP transparent mode
D.implement VTP version 3
A. prefixes received from any other BGP peer and prefixes locally originated via networkstatements or redistributed to BGP
B. all prefixes in its IP routing table
C. only prefixes received from EBGP peers and prefixes locally originated via network statements or redistributed
D. only prefixes received from EBGP peers and prefixes received from route reflectors
E. all prefixes in its routing table except the prefixes received from other EBGP peers
F. all prefixes in its routing table except the prefixes received from other IBGP peers
最新试题
In GLBP，which router will answer on client ARP requests？（）
When STP UplinkFast is enabled on a switch utilizing the default bridge priority， what will the new bridgepriority be changed to？（）
Which message type is constructed and sent from an MSDP router to its MSDP peers when it receives a PIM register message knowing that the MSDP router is also configured as an RP for the PIM domain？（）
Which of these statements about penultimate hop popping are true？（）
The classic Spanning Tree Protocol （802.1 D 1998） uses which sequence of variables to determine thebest received BPDU？（）
On the basis of the network provided in the exhibit， all routers are configured to run EIGRP on all links. If the link between PG-R1 and PG-R2 fails， what is the maximum number of queries PG-R3 will receive for 192.168.1.0/24， assuming that all the packets sent during convergence are transmitted once （there are no dropped or retransmitted packets）？（）
Which multicast address is reserved for cisco-rp-discovery？（）
Which of the following is true about the MPLS header and its EXP field size？（）
Which types of prefixes will a router running BGP most likely advertise to an IBGP peer， assuming it is notconfigured as a route reflector？（）
Which two of these are used in the selection of a root bridge in a network utilizing Spanning Tree ProtocolIEEE 802.1 D？（）