When does auxiliary burner of rotary nozzle incinerator begin to work? ()
Ⅰ.hen igniting
Ⅱ.he sludge for dealing with is too much
Ⅲ.efore stopping incinerator
A.Ⅰ+Ⅱ
B.Ⅰ+Ⅲ
C.Ⅱ+Ⅲ
D.Ⅰ+Ⅱ+Ⅲ
您可能感兴趣的试卷
你可能感兴趣的试题
A.After stopping supplying sludge oil, the value and pipe should be flushed by flushed by diesel oil and the incinerator continue burning for 10 minutes
B.Close auxiliary burner firstly and then close main burner
C.After stopping fuel, restoring the position of main fuel supply valve
D.Stop blower as soon as stopping supplying fuel oil
A.Scavenging time should be more 30 seconds before igniting
B.The temperature of sludge tank is 80~100℃
C.First igniting the incinerator with diesel oil, when the temperature of health is about 600℃, the sludge oil drawn in
D.The ash can be dumped into sea when the distance is more than 3 miles from land
When does auxiliary burner of incinerator put into operation? ()
Ⅰ.tart incinerator when it is cold
Ⅱ.he sludge for dealing with is little
Ⅲ.he sludge for dealing with is large
Ⅳ.he water and impurity in sludge are too much
Ⅴ.he temperature in incinerator is low
Ⅵ.ealing with little solid rubbish
A.Ⅰ+Ⅱ+Ⅲ+Ⅴ
B.Ⅰ+Ⅱ+Ⅲ+Ⅳ
C.Ⅰ+Ⅳ+Ⅴ+Ⅵ
D.Ⅰ+Ⅱ+Ⅲ+Ⅵ
A.filled with clean water before operation
B.keep air cushion in oil collecting space during running
C.check oil level during running
D.clean inner separator with low pressure stream
A.pay attention to operating parameters
B.renew and clean separating units in time
C.check oil level in separator to prevent overload
D.check separating effect, if it is bad, flush with large capacity water pump
A.overhauling every two year
B.working at intervals
C.renewing filtration material
D.pumping bilge water from different layers respectively
A.working at intervals and properly heating
B.warming up to 70℃, increase water supply flow
C.improving impulse of water supply
D.reducing water supply flow
A.flushing separator with hot water
B.increasing water supply flow
C.heat oily water properly
D.opening manual oil discharge value
A.the separator is overload
B.the monitor equipment of separator fails
C.the discharge pump of separator can not work
D.the temperature of oil water is low
A.15;inlet value
B.15;inlet and outlet value
C.30;inlet value
D.30;inlet and outlet value
最新试题
To shut down a diesel engine after it exceeds the set maximum speed,which type of device listed should be used?()
For a given exhaust gas boiler, what is the quantity of its evaporation mainly determined?()
The ISPS Code consists of a mandatory section-Part A, which shows()
Engine parameters shall be corresponded to NOx Technical Files. This is required by ()
A purge recovery system is used in a centrifugal air conditioning or refrigeration system to ()
One of the reasons that cause oil flowed from sludge outlet of a self-cleaning separator is()
Which of the following items don’t belong to dock repair works?()
() is not installed on the main switchboar.
Flame failure in an automatically fired auxiliary boiler can from a/an ()
As soon as a diesel engine has started, which of the listed engine operating parameters should be checked FIRST?()